GQF型伸缩缝的安装：

GQF type expansion joint installation

安装方式：

Installation method

a、安装时，按实际温度确定其安装宽度值。

When the A is installed， the value of the installation width is determined at the actual temperature.

b、伸缩缝安装过程，必须使用伸缩缝装置整齐排列，保持一定的倾斜度。确保伸缩装置的高平面与完工的桥面相平。

B， expansion joint installation process， must use the expansion joint arrangement in order， to maintain a certain inclination. Ensure that the maximum plane of the telescopic device is flat with the completed bridge.

c、施工方法

C and construction methods

清理槽口，使之达到设计宽度和深度，清除与位移箱埋入有干扰的钢筋，预留坑的开口必须大于伸缩缝的安装宽度。

First， clear the notch to make the design width and depth clear， and remove the reinforced steel embedded in the displacement box. The opening of the reserved pit must be larger than the installation width of the expansion joint.

检查伸缩装置的各梁之间间隙是否符合安装温度要求，否则，应用水平千斤顶、夹具进行调整直至符合设计要求，调整好后，立即安上专用夹具。

Second， check whether the gap between the beams of the telescopic device meets the installation temperature requirements. Otherwise， if the horizontal jack and fixture are adjusted， until the design requirements are met， after adjustment， a special fixture is immediately installed.

根据伸缩缝中心位置设置起吊装置，将伸缩装置安入在槽口内，并使伸缩装置的顶面与桥面标高相同。同时注意纵横坡也应与桥面相符。

The lifting device is set according to the center position of the expansion joint， and the telescopic device is installed in the slot， and the top surface of the telescopic device is the same as the elevation of the bridge surface. At the same time， it should be noted that the vertical and horizontal slope should be consistent with the bridge surface.

伸缩装置吊入预留槽后，其中心线应与梁端预留间隙中心线对正，其长度与桥梁宽度对正。

After the telescopic device is hoisted into the reserved slot， the center line should be correct with the center line of the clearance of the beam end， and its length is positive to the width of the bridge.

对伸缩装置直线段进行调整，并使各纵梁的缝隙均匀一致。

Adjust the straight-line section of the telescopic device and make the cracks of the longitudinal beams uniform.

再在伸缩装置箱体或锚固板处，立焊16以上的钢筋进行高度定位，横焊16钢筋进行宽度定位。

Then the expansion device box or anchor plate， height positioning welding with reinforced by more than 16， the width of the transverse welding positioning with 16 steel.

伸缩装置正确就位锚固后，便可以将伸缩装置一侧的锚固钢筋和预留槽预留钢筋焊接以保证伸缩装置线向固定并找平，焊接时只要每隔23个锚固筋焊接一个即可，然后再按上述步骤 焊接另一侧的锚固筋。待两侧达到固定后，就可将其余焊接的锚固筋再进行焊接，确保可靠锚固。在焊接锚固筋时要注意不要在边梁和中梁上任意施工焊，以防钢梁发生扭曲变形。

The expansion device is correctly positioned after anchoring， anchoring steel telescopic device can be on one side of the slot is reserved and welded steel to ensure the expansion device to the fixed line and leveling， welding as long as every 2 3 anchoring steel welding a can， and then according to the steps of welding the other side of the anchor bar. After the two sides are fixed， the rest of the welded anchorage can be welded to ensure the reliable anchorage. In order to prevent the distortion and distortion of the steel beam， no construction welding on the side beam and the middle beam should be paid attention to in the welding of the anchorage reinforcement.

伸缩装置如果分段安装，接缝处必须焊接，焊接应由专业人员进行，每根梁焊好后，再按步骤进行锚固。

The expansion device if the segment joint must be installed， welding， welding should be professional， each beam welding， according to the steps of anchorage.

根据缝的外形尺寸和预留槽口制作模板，模板放好后应遮挡严实，以防水浆流入位移箱内，伸缩缝上平面加盖板，以防砂浆落入橡胶密封带，在检查装置的正确平整度和中线位置，以 及缝隙是否均符合要求后，方可灌入混凝土，并对混凝土充分振捣压实，尤其应注意位移箱与预留坑基面不能留下空洞。待混凝土固化后撤去模板和伸缩缝上的固定卡。

According to the shape and size to seam reserved template template slot in place， should cover tightly， with waterproof slurry inflow displacement box， expansion joints on the plane and cover， to prevent falling into the mortar with rubber seal， the inspection device correct flatness and the midline， and the gap is not meet the requirements， can pouring concrete， concrete and vibrating compaction on full vibration， especially should pay attention to the displacement and the reserved box can not leave the empty pit base. Fixed card removed template and expansion joints on the concrete to be cured.

在伸缩缝处混凝土未达到80%的强度前，伸缩缝不能承受外来荷载作用。

In the expansion joints of concrete strength did not reach 80% before， can not withstand external load expansion joint.